Nment of the cell while RI = +1 represents perfect alignment of the cell in direction of the cue gradient or EFPLOS ONE | DOI:10.1371/journal.pone.0122094 March 30,13 /3D Num. Model of Cell Morphology during Mig. in Multi-Signaling Sub.direction. Consequently, in the presence of a cue gradient or dcEF, the closer RI to +1, the lower the cell random orientation.Numerical examples and resultsDuring cell migration, amoeboid mode of cells causes frequent changes in cell shape as a result of the extension and retraction of protrusions [20]. To consider this, four different categories of numerical examples have been represented to consider cell behavior in presence of different stimuli. All the stimuli such as thermotaxis, chemotaxis and electrotaxis are considered within the matrix with a linear stiffness gradient and free SCH 530348MedChemExpress SCH 530348 boundary surfaces. It is assumed that, initially, the cell has a spherical configuration. Each simulation has been repeated at least 10 times to evaluate the results consistency.Cell behavior in a 3D matrix with a pure mechanotaxisExperimental investigations demonstrate that cells located within 3D matrix actively migrate in direction of stiffness gradient towards stiffer regions [103]. In addition, it has been observed that during cell migration towards stiffer regions, the cell elongates and subsequently the cell membrane area increases [13, 96]. To consider the effect of mechanotaxis on cell behavior, it is assumed that there is a linear stiffness gradient in x direction which changes from 1 kPa at x = 0 to 100 kPa at x = 400 m. The cell is initially located at a corner of the matrix near the boundary surface with lowest stiffness. Fig 5 and Fig 6 show the cell configuration and the trajectory tracked by the cell centroid within a matrix with stiffness gradient, respectively. As expected, independent from the initial position of the cell, when the cell is placed within a substrate with pure stiffness gradient it tends to migrate in direction of the stiffness gradient towards the stiffer region and it becomes gradually elongated. The cell experiences a maximum elongation in the intermediate region of the substrate since it is far from unconstrained boundary surface which is SCH 530348MedChemExpress SCH 530348 discussed in the previously presented work [66]. As the cell approaches the end of the substrate the cell elongation and CMI decrease (see Fig 7). Despite the boundary surface at x = 400 m has maximum elastic modulus, due to unconstrained boundary, the cell does not tend to move towards it and maintains at a certain distance from it. The cell may extend random protrusions to the end of the substrate but it retracts again and maintains its centroid around an imaginary equilibrium plane (IEP) located far from the end of the substrate at x = 351 ?5 m (see Fig 8) [69]. Therefore, the cell never spread on the surface with the maximum stiffness. It is worth noting that the deviation of the obtained IEP coordinates is due to the stochastic nature of cell migration (random protrusion force). Fig 8 represents cell RI for the imposed stiffness gradient slope. The simulation was repeated for several initial positions of the cell and several values of the gradient slope, all the obtained results were consistent. However, change in the gradient slope can change the cell random movement and slightly displace the IEP position (results of different gradient slopes are not shown here). Cell behavior within the substrate with stiffness gradient is in agreement with exp.Nment of the cell while RI = +1 represents perfect alignment of the cell in direction of the cue gradient or EFPLOS ONE | DOI:10.1371/journal.pone.0122094 March 30,13 /3D Num. Model of Cell Morphology during Mig. in Multi-Signaling Sub.direction. Consequently, in the presence of a cue gradient or dcEF, the closer RI to +1, the lower the cell random orientation.Numerical examples and resultsDuring cell migration, amoeboid mode of cells causes frequent changes in cell shape as a result of the extension and retraction of protrusions [20]. To consider this, four different categories of numerical examples have been represented to consider cell behavior in presence of different stimuli. All the stimuli such as thermotaxis, chemotaxis and electrotaxis are considered within the matrix with a linear stiffness gradient and free boundary surfaces. It is assumed that, initially, the cell has a spherical configuration. Each simulation has been repeated at least 10 times to evaluate the results consistency.Cell behavior in a 3D matrix with a pure mechanotaxisExperimental investigations demonstrate that cells located within 3D matrix actively migrate in direction of stiffness gradient towards stiffer regions [103]. In addition, it has been observed that during cell migration towards stiffer regions, the cell elongates and subsequently the cell membrane area increases [13, 96]. To consider the effect of mechanotaxis on cell behavior, it is assumed that there is a linear stiffness gradient in x direction which changes from 1 kPa at x = 0 to 100 kPa at x = 400 m. The cell is initially located at a corner of the matrix near the boundary surface with lowest stiffness. Fig 5 and Fig 6 show the cell configuration and the trajectory tracked by the cell centroid within a matrix with stiffness gradient, respectively. As expected, independent from the initial position of the cell, when the cell is placed within a substrate with pure stiffness gradient it tends to migrate in direction of the stiffness gradient towards the stiffer region and it becomes gradually elongated. The cell experiences a maximum elongation in the intermediate region of the substrate since it is far from unconstrained boundary surface which is discussed in the previously presented work [66]. As the cell approaches the end of the substrate the cell elongation and CMI decrease (see Fig 7). Despite the boundary surface at x = 400 m has maximum elastic modulus, due to unconstrained boundary, the cell does not tend to move towards it and maintains at a certain distance from it. The cell may extend random protrusions to the end of the substrate but it retracts again and maintains its centroid around an imaginary equilibrium plane (IEP) located far from the end of the substrate at x = 351 ?5 m (see Fig 8) [69]. Therefore, the cell never spread on the surface with the maximum stiffness. It is worth noting that the deviation of the obtained IEP coordinates is due to the stochastic nature of cell migration (random protrusion force). Fig 8 represents cell RI for the imposed stiffness gradient slope. The simulation was repeated for several initial positions of the cell and several values of the gradient slope, all the obtained results were consistent. However, change in the gradient slope can change the cell random movement and slightly displace the IEP position (results of different gradient slopes are not shown here). Cell behavior within the substrate with stiffness gradient is in agreement with exp.